Vertical Shelf For Flowers. How To Do It Yourself. A Photo

Table of contents:

Vertical Shelf For Flowers. How To Do It Yourself. A Photo
Vertical Shelf For Flowers. How To Do It Yourself. A Photo

Video: Vertical Shelf For Flowers. How To Do It Yourself. A Photo

Отличия серверных жестких дисков от десктопных
Video: MINIMALIST DIY PICTURE SHELF 2023, February
Anonim

The reason that prompted me to make another shelf for flowers, my mother-in-law. Seeing such houses in my house, she very "transparently hinted" that she wants her own kind. And to the question, which one, she answered like all women: “original and interesting, in short a kind”.

Vertical flower shelf
Vertical flower shelf

However, as for me, it is very difficult to come up with something non-standard such a rather utilitarian thing as a shelf for flowers, without disrupting its functionality. But I tried it and it worked out well. But first things first.

The first thing I needed were pieces of chipboard. I did not buy them, and in the workshop where large sheets are cut, there are always scraps. Good sawers allowed them to collect in plenty, which I did not fail to use. This flower rack is made of nine pieces, measuring 14 by 20 centimeters. Although, if you want to repeat my experience, you can vary them. And you will be convinced of this now.

Chipboards sawn to size
Chipboards sawn to size

You will also need a small hammer or mallet, a shoe knife, a drill-screwdriver, bits - cross and hex, as well as an extension cord for them, a confirmation and simple drill with a diameter of 6.5 … 7 mm, a block with sandpaper, a simple device for pasting with an edge, an iron, the edge itself, ten circles for gluing the heads of confirmations (as it turned out later, they were not needed), six dowels, PVA glue, and hardware.

Hammer
Hammer
Shoe knife
Shoe knife
Drill-screwdriver
Drill-screwdriver
Confirmable and simple drill, diameter 6.5 … 7 mm
Confirmable and simple drill, diameter 6.5 … 7 mm
Edge banding device
Edge banding device
Edge tape
Edge tape
Furniture plugs for confirmations
Furniture plugs for confirmations
Dowels or chopiki
Dowels or chopiki
PVA glue
PVA glue

Ten confirmations, six self-tapping screws 16 mm long, and two 45 mm long with a large head. In addition, two long sheds will be needed.

Confirmation certificate ("Euro screw", "screw tie", "Euro screw"
Confirmation certificate ("Euro screw", "screw tie", "Euro screw"
Self-tapping screws
Self-tapping screws
Self-tapping screws
Self-tapping screws
Furniture awnings
Furniture awnings

Let's get to work, especially since it is very simple

We glue pieces of chipboard with an edge (an iron will help you), and cut off the excess with a knife and clean it with sandpaper.

Pieces of chipboard are pasted over with an edge
Pieces of chipboard are pasted over with an edge
We cut off the excess with a knife and clean it with sandpaper
We cut off the excess with a knife and clean it with sandpaper

True, those fragments that will form the basis of our flower shelf are pasted over only to the middle, and we also cut off excess edges.

Fragments that make up the base are pasted over to the middle
Fragments that make up the base are pasted over to the middle
Cut off excess edges
Cut off excess edges

Drill two holes in the non-glued edge of the part, and drive two dowels into the glue.

Drill two holes in the non-glued part
Drill two holes in the non-glued part
Pour the glue inside and drive in two dowels
Pour the glue inside and drive in two dowels

In the counterpart, we also drill two holes, pour the glue inside and on the end, and connect both parts.

In the counterpart, we also drill two holes, pour the glue inside and on the end
In the counterpart, we also drill two holes, pour the glue inside and on the end
We connect both parts
We connect both parts

We also connect the other two parts of the base, and if you have shifted the dimensions, just press them with a clamp until they are completely dry.

We also connect the other two parts of the base
We also connect the other two parts of the base

The glue is dry. Now we also connect both halves with dowels and glue, press again with a clamp and leave to dry for several hours.

We connect both halves with dowels and glue
We connect both halves with dowels and glue

Now we mark the base of the future flower shelf, drill holes, and fasten the cells themselves, alternating them to the right and left.

We mark the basis of the future flower shelf
We mark the basis of the future flower shelf
Drilling holes
Drilling holes
We fasten the cells themselves, alternating them to the right and left
We fasten the cells themselves, alternating them to the right and left

Now we screw in the awnings, erase the markings, and glue the heads of the confirmations.

Now we screw in the awnings, erase the markings and glue the heads of the Euro screws
Now we screw in the awnings, erase the markings and glue the heads of the Euro screws

The flower rack is ready.

Vertical flower shelf
Vertical flower shelf

We hang it by screwing it to a dense and even surface with self-tapping screws. The canopies were deliberately screwed in, and vice versa, outward, so that the screws would tighten it. So the shelf for flowers will not fall off even with careless movement. So I made a vertical flower rack. Now it's your turn.

Popular by topic